|
|
NEW for 2008! - Second Bedroom
The new Second Bedroom is 2100mm long and 1675mm wide and weighs approx 5kgs. It is made of lightweight polyester, is mildew resistant, UV stable and Waterproof – similar to that used in heavy duty lightweight tents.
It can sleep 3 Children or 2 adults comfortably. It can be zipped on in a single action in minutes.
The floor is sewn in so it is a one piece item
The floor is high quality PVC able to be a barrier to water and moisture in the ground. It rises above the ground by approx 75mm
The entry into and out of the bedroom is through the rear Kamper Mesh Door (was a window in prior models)
There is one large window on the Kitchen Side which has a zipped over cover from the outside.
There are NO POLES . There are 2 pegs and optional ropes needed.
It still allows the Ensuite Bathroom to Zip onto side.
|
|
|
NEW for 2008! - KWIK Awning
2m wide x 6.7m long (for older models 6.3mLong). Stays Zipped onto Kamper all the time.
The 2 end triangular corners fold under the awning roof and Velcro up underneath. In this configuration, the awning is a parallelogram shape.
There are 2 poles that are overhead bars which “push” the awning out with web tabs sewn onto the awning to receive the small post of the pole. These roof poles are supported by J clamps and vertical 45 degree (approx) poles that clip onto the kamper body (we are using the over centre catch base piece also used to close the camper. Because the awning cant be erected with a closed camper there is no conflict of use.
To adjust the awning, the vertical bars are pushed out further. The awning has a scalloped edge.
When you need more cover and/ or the wind picks up, the 2 end sections are pulled away from Velcro and poles are used in the usual way.
THIS IS RETROFITABLE TO ALL KIMBERLEY KAMPERS FROM 2002 onwards
|
|
|
NEW for 2008! - Delta™ Gullwing
Delta™ Gullwing has 3 points of storage access for more dedicated storage for faster setup. It is 1300litres, 30% bigger than 2007 Model and more efficient with external pole carrier. Revised design offers maximum flexibility in the selection of internal fit-out of the Delta™ Gullwing.
Available for the new 2008 Kimberley Kamper and Kimberley Kamper ‘Platinum’ models only.
|
|
|
”Master” Kitchen Slide
Our biggest Kitchen Slide change since 2003. We've utilised Industrial Design to put you, the user, at the core of the design process. The NEW 2007 Master Kitchen offers increased storage capacity, better functionality and a more user friendly layout. When combined with the new Dual Cookers arangement a convenient "U" shape kitchen work area is created where two people can work comfortably at the same time.*
*Dual Cookers is a standard feature on the ‘Platinum’ model
|
|
|
Diesel Hot Water System (optional)
"Hot water: On-board and On-demand." That was our aim for this design and our new Diesel Hot Water System delivers just that! Just press a button, allow system to heat up, then enjoy your hot water on-demand. This compact system is diesel powered, virtually odorless and safer than LPG. It uses a heat exchanger and does not require a hot water holding tank.
This system also includes Visi-flow™ system which allows automatic pumping from a nearby stream or billabong for endless hot water.
|
|
|
Aluminium Gullwing™ Storage
We've taken the proven Gullwing storage pack and added the convenience of slide-out Dual Cookers. Higher-intensity LED strip light better illuminate the work area. When combined with the NEW 2007 Master Kitchen a convenient "U" shape kitchen work area is created where two people can work comfortably at the same time.
|
|
|
Dual Layer Mattress
All models feature the NEW Dual Layer Mattress. Designed for superior comfort, this specially constructed mattress provides a supportive base with a soft comfortable top. These layers are permium quality foam and are bonded together. This mattress is exclusively supplied for Kimberley Kampers.
|
|
|
Aluminium Alloy Front Frame
To reduce draw-bar weight even further, we have developed an Aluminium Alloy Front Frame. This component weight is now close to 50% lighter than the steel front frame used in 2006 models. The frame utilises a bead-blast finish to improve appearance & durability.
|
|
 
|
Mariner Pro Pak
This Pak alloys you to store your boat, outboard and a folding boat trailer with your Camper. The folding boat trailer is compact, stored in front of the Gullwing Pak and erects quickly. The trailer comes standard with a treg hitch and light board for road registration. Your boat can stay on the boat loader as you open the Camper and the outboard slide makes it easy to store and handle your outboard.
|
|
|
Gullwing™ Storage
The secret to our trademark Gullwing pantry and cooking area is it’s compactness and ease of access. Our design provides overhead protection as well as overhead light. Our patented fan forced filtration system means the heat from your fridge/freezer can exhaust without getting the dust in! We use stainless steel glideout pantry and fittings.
The integrated LED Flexi-Strip™ is on both sides of the Gullwing.
|
|
|
Kamp-Dry™ Tenting
To achieve the ultimate in water proofing, the best canvas is used with the finest stitching on proven designs.
Our trained staff use ultra-fine needles, 2 sizes smaller than the manufacturers recommend; and their quality of workmanship is superior.
All the canvas is both designed and made by us in our factory.The designs avoid multiple seams on pressure areas by giving both strength and seam tightness
|
|
|
Deflecta-Shield™ System
We use a double point shield system: Under the camper, there is a steel stone deflecta shield. Above the chassis, the front deflecta shield is a separate stone guard. On the side are 2 sets of wide Mudflaps and Stainless steel protection strips
|
|
|
Hi-Top Tropical Roof™
This unique roof stays on the camper all the time and automatically erects when the camper opens. It's hi-top patented design allows excellent air flow in summer and minimizes condensation inside the camper in winter. It also protects the camper roof from falling debris and stains. It has withstood wind gusts of up to 30 knots.
|
|
|
Selecta-Swing-Away™
Our Chassis has on the drivers side rear, a reinforced channel ready for the optional Selecta-Swing-Away™ carriers. These are attached through compression sleeves and have a cam adjustable swing mechanism with safety catch and stainless securing lock. There are 5 different carrier arm to select from:
Triple Jerry can holder in alloy frame and "Rhino Tuff" lined; Spare Wheel and single Jerry can holder in Galvanised steel; outboard motor carrier in galvanised steel; utility plate with posts of galvanised steel; 50mm receiver welded into central position of galvanised arm so a rear bicycle carrier can be located and interchanged with the rear of vehicle.
|
|
|
Dual-Skin™ Construction
We use a unique construction process of building a metal trailer with a zinc anneal outer skin and inserting a one piece polyethylene liner as an inner skin which gives better insulation and enables a dust proof shell. The canvas tent is locked between the layers.
|
|
|
LaserLocked™ Chassis
To achieve the lowest weight for maximum strength, we have developed a laser cut chassis that interlocks together. It self jigs on a flat table eliminating any error. The interlock sections penetrate through the chassis with but welds for maximum strength and a quality finish.
The is the first laser cut and interlocked chassis in the camper trailer industry.
|
|
|
Fatigue-Shield™ for Alloy Construction
Alloy and Fibreglass materials suffer from fatigue in constant impact conditions. Our solution is a patented adhesion with a Polyurethane Elastic Adhesive of the alloy or fibreglass material to hot dipped galvanized sub-frames. The result is significantly lighter weight but without the fatigue cracking common in alloy only construction.
|
